HFWORKS and ATLASS RF

A Leading Provider Of Telemetry Equipment Since 1993

Bit Error Rate Testers We offer a broad range of Bit Error Rate Testers, including turnkey and board level products. These products are used for testing synchronous serial or 8-bit parallel communications equipment, communications links, and radio telemetry systems.
Clock Synthesizers Our Clock Synthesizers are a programmable frequency sources designed as an alternative to expensive frequency synthesizers in telemetry systems that require a synthesized clock source.
Digital Data Recorders / Reproducers We offer an extensive line of high-performance Digital Data Recorders / Reproducers based on disk and tape technologies. These products are suitable for spacecraft to ground and aircraft to ground telemetry recording and for development of telemetry systems.
Network Telemetry Links Our single-channel and dual-channel Network Telemetry Links are intended for applications that require transmission of serial or parallel telemetry data streams across a network at data rates up to 800 Mbps (serial) or 100 MBps (parallel) per channel.
System Integration Services Reach Technologies has over 25 years of telemetry system integration experience.
Telemetry Crossbar Switches Our Telemetry Crossbar Switches are designed to switch and distribute clock and data telemetry signal pairs at data rates up to 2 Gbps. The switches have a non blocking architecture designed to route any of the input signals to any of the outputs available on the switch. Our switch products range from 4x4 non-redundant to 128x128 redundant configurations.
Telemetry Interfaces Our Telemetry Interfaces are designed for applications that require the input and output of serial telemetry data into PCI based computer systems. These products are used in remote sensing ground stations, satellite command and control systems, and range telemetry applications.

Miteq's all new Amplifier Components

High Power Amplifier Model AMF-5B-09001050-40-39P provides 7 Watts of X-band power. and a has an output P1dB of about 39 dBm from 9 to10.5 GHz and 38 dBm from 7.5 to 11 GHz. Gain is 36 dB minimum, ± 1 dB flat, and typical noise figure is 3.5 dB. This model operates from -10 to +60 ° C base temperature range and draws about 4A from 15 V. It has internal regulation and protection, and a footprint of only 3.3 inch x 3.3 inch.

Broadband Power Amplifier Model AMF-2B-00030300-150-32P is a 2W amplifier, offering 20 dB of gain from 30 MHz to 3 GHz. The 24V voltage required is also internally gated by the external -5V to minimize any chance of damage. Very compact, 2 inch by 2 inch by 0.5 inch, housing has two SMA connectors and can be bolted on a heat sink. It draws 600 mA maximum and has a typical noise figure of about 8 dB and an input match of 1.5:1 maximum.

26-31 GHz 5W Power Amplifier AMF-4B-26003100-100-36P is a connectorized high-power amplifier/module, covering 26-31 GHz and delivering approximately 5W of power. The Female K-type connectorized aluminum housing is 10mm (H) x 25mm (L) x 34mm (W). It is intended for bolting to a flat cooling surface or fins. Housing is environmentally sealed and EMI shielded. Hermetic sealing option is also available. Nominal small-signal gain is near 18 dB. Current draw is nominally 7A at P1dB from 6-6.5 VDC of supply and -1.25 VDC.

43.5-45.5 GHz Waveguide Amplifier AMFWW-10F-43504550-50-25P has 35 dB minimum gain over the full band, with a minimum P1dB of 25 dBm. Typical noise figure is 5 dB. UG383/U waveguide input and output ports have a low VSWR of 1.5:1. It typically draws 1A from a 15V supply. Picture shown does not include isolators. This amplifier has built in regulation, reverse bias protection and TTL control is optional. It includes a custom heat sink that can be removed. Other models from 15 dBm to 30 dBm are also available.

Q-Band Waveguide Limiter LNA Model AMFW-5F-33004000-50-10P-4WL is a very low noise Q-Band waveguide front end. WR-28 waveguide input and output amplifier is very lightweight and has an extremely small profile and footprint. Aluminum alloy housing is environmentally sealed and EMI shielded. Hermetic sealing option is also available. LNA includes reverse voltage, over current and over temperature protection, in addition to full internal regulation. This amplifier is capable of a minimum of 10 dBm of P1dB across the full band, 33-40 GHz. Built-in limiter can prevent damage from up to 5W of CW input. Port VSWR is a maximum of 2.5:1 but typically 2:1 or less. Nominal small-signal gain is minimum 18 dB and maximum of 22 dB while the noise figure is less than 5 dB. Gain flatness is 2 dB peak-to-peak typical. Current draw is nominally 165 mA from a single positive 15V supply.

1-8 GHz 1 W Power Amplifier Model AMF-4D-01000800-85-30P is a connectorized small outline high-dynamic range amplifier, covering multi-octave bandwidth from 1-8 GHz. The housing is 23mm (H) x 18mm (L) x 8mm (W) without the connectors and heat sink. The amplifier is environmentally sealed, EMI shielded and includes reverse voltage protection, in addition to full internal regulation. Nominal small-signal gain is a minimum of 28 dB while noise figure is less than 8 dB across the full band. Maximum gain variation is less then +/-1.5 dB typically over the full frequency band and temperature range. Current draw is nominally 1000 mA at P1dB from a single 15 VDC supply. Minimum P1dB is typically 30 dBm. Port VSWR is typically less than 2:1 for the full band also.

8-18 GHz Broadband High Power Amplifier Model AMF-2B-08001800-55-35P is a connectorized high power amplifier, covering octave bandwidth from 8-18 GHz and delivering approximately 3W of power and 2.5W from 6-18 GHz. In the band of 10-15 GHz, it delivers about 7W of P1dB. The SMA connectorized aluminum housing is 21mm (H) x 95mm (L) x 66mm (W). It is intended for bolting to a flat cooling surface or fins. Housing is environmentally sealed, EMI shielded and hermetic sealing option is also available. Power Amplifier includes reverse voltage protection, in addition to full internal regulation. A TTL-control pin is optional. Nominal small-signal gain is 50 dB while noise figure is better than 5 dB across the band. Current draw is nominally 6.2A at P1dB from 12 to 15 VDC of supply. Output IP3 is a minimum of 44 dBm across the full band, closer to 47 dBm from 10–15 GHz.